Senior Engineer Job Vacancies in Nashik

Designation- Prod.SR. production engineerReporting (Functional) ASST- Production ManagerDepartment Production Qualification BE-MechanicalExperience 8 YearII) Responsibilities: Required Skill: (Technical & Behavioural)1. KAIZEN 2. TPM3. SPC, MSA 4. SIX Sigma 5.IAIF6.MSESRequired Knowledge:1. Make Production planning as per customer requirement2. Monitor shop floor production activities as per daily prod plan.3.Monitoring process as welding process, robot spot, manual spot, projection & co2 welding & all line documents.4. To conduct morning Meeting with Operator & line Engg. To discussed as mention in morning meeting agenda.5. Monitoring daily losses during production and action plan& productivity.6. Audits all line process including K- card audits DWM meeting.7. Do IATF, MSES, QMS Audits preparation make review and actions.8. Monitoring EOHS and MRM data & to attain management level meetings.9.Continual Improvement through kaizens, cost savings. 10.Custmoer complaint review and action plan if customer complaint there.11.Monitor Process validation as per control plan.12.Monitor 5S at shop floor and safety.13.Lead TPM activities as per plan. Attend meeting make preparation of planned machines as per JH TPM plan.14.Monitoring inhouse defects and its action plan, also process rework, rejection PPM.15.Evalate operators skill level and make skill matrix for operators.16.Mail communication to supporting department regarding any failures. 17.Monitoring manpower cost vs seal cost at BIW production department.18.To attend external audits which was conducted at plant level such as, IATF, MSES, EOSH, HELTH AND SAFETY, QMS audits.19.Monitor Daily child part shortage& coordinate with team.20.Skill required, NC handling, manpower handling, customer handling &customer focus work.21.Monitoring &Update production data, and loss data, productivity, manpower data every day and month wise. 22.Monitor &control KPI, Objective all sections staff.

Efficiently Process predefined number of transactions as assigned with highest level of accuracy as agreed upon by the client.Provide highest level of customer satisfaction.Strive to understand and resolve issues/queries at the first instant.Maintain the business controls as per the requirement.Articulate/ communicate in a manner which is understood by clients / end users.Connect & provide highest level of satisfaction to the customer.CT:HR BHAVANI

Key ResponsibilitiesElectrical System Design: Design internal and external electrical layouts, including High Voltage/Low Voltage (HV/LV) power distribution networks, sub-stations, transformer sizing, and DG (Diesel Generator) backup systems.Lighting & ELV Design: Create comprehensive indoor/outdoor lighting layouts, lux level calculations, emergency lighting networks, and Extra-Low Voltage (ELV) systems (including CCTV, fire alarms, PA systems, and data networks).Engineering Calculations: Perform precise technical calculations for cable sizing, voltage drop, short circuit analysis, capacitor bank requirements, and protective earthing/lightning protection networks.Drafting & Schematics: Develop detailed 2D electrical single-line diagrams (SLDs), power schematics, conduit routing layout plans, and panel schedules using AutoCAD.BOQ & Tendering: Prepare comprehensive Bill of Quantities (BOQ), detailed material specifications, cost estimations, and technical data sheets for vendor tendering and procurement.Codes & Compliance: Ensure all electrical engineering designs strictly conform to the National Electrical Code (NEC), National Building Code (NBC), Indian Electricity (IE) Rules, and local state electricity board regulations (e.g., MSEDCL guidelines).Site Coordination: Review shop drawings submitted by electrical contractors on-site, address technical queries (RFIs), and conduct periodic site inspections to ensure installation matches design specifications.

Job Description Senior Design EngineerDepartment: Design & EngineeringIndustry: Metal Manufacturing / Sheet Metal / FabricationJob PurposeTo lead and execute design activities for metal components and assemblies, optimize designs for manufacturability, and drive continuous improvement using AutoCAD and Kaizen methodologies.Key ResponsibilitiesCreate and review detailed AutoCAD drawings for metal parts and assemblies.Design sheet metal, fabrication, welding, and machined components.Lead design reviews and ensure manufacturability and cost optimization.Coordinate with production, quality, purchase, and sales teams.Handle customer drawings, RFQs, and technical discussions.Implement Kaizen initiatives to improve design efficiency, reduce waste, and optimize processes.Support tooling development, jigs, and fixtures.Guide and mentor junior design engineers.Ensure compliance with quality, safety, and industry standards.Required SkillsStrong proficiency in AutoCAD (2D & basic 3D preferred).In-depth knowledge of metal manufacturing processes.Strong understanding of GD&T, tolerances, and BOMs.Practical knowledge of Kaizen, lean manufacturing, and continuous improvement tools.Problem-solving and analytical skills.Leadership and team coordination skills.QualificationsBE / BTech in Mechanical or Production Engineering.Experience510 years in design engineering within the metal manufacturing industry.