Fresher Service Engineer Jobs

We are looking for Field Service Engineers to handle installation, configuration, troubleshooting, servicing, calibration, and maintenance of CCTV, Access Control Systems, Fire Alarm Systems, and Public Address (PA) Systems.Key Responsibilities Installation of CCTV, Access Control, Fire Alarm and PA equipment Cable laying and installation work System configuration and programming Troubleshooting and servicing of equipment Calibration and preventive maintenance Data connectivity and system configuration Prepare and maintain service reports Visit customer sites for installation and service activities

Job TitleAircraft Maintenance Engineer (AME)DepartmentAircraft Maintenance / EngineeringLocationsPuneMumbaiNagpurNashikShirdiGoaAmravatiAurangabadKolhapurNavi MumbaiSolapurJob SummaryAn Aircraft Maintenance Engineer (AME) is responsible for inspecting, maintaining, repairing, troubleshooting, and certifying aircraft to ensure they are safe, airworthy, and compliant with aviation regulations. The role involves carrying out scheduled and unscheduled maintenance on aircraft systems, engines, avionics, electrical components, hydraulic systems, landing gear, and structural components while adhering to the standards established by aviation authorities.Key ResponsibilitiesAircraft Inspection & MaintenancePerform routine, preventive, scheduled, and unscheduled aircraft maintenance.Conduct daily, transit, weekly, A-check, B-check, C-check, and heavy maintenance inspections.Inspect aircraft structures, fuselage, wings, landing gear, flight controls, and engines.Diagnose and rectify aircraft defects using approved maintenance procedures.Replace, repair, and overhaul defective aircraft components.Ensure all maintenance tasks are completed according to the Aircraft Maintenance Manual (AMM).Troubleshooting & RepairsIdentify mechanical, hydraulic, electrical, pneumatic, and avionics faults.Use specialized diagnostic tools and testing equipment.Repair aircraft systems while maintaining manufacturer specifications.Coordinate with engineering teams for complex technical issues.Perform functional tests after repairs to verify serviceability.Engine & Component MaintenanceInspect aircraft engines for wear, leaks, corrosion, and damage.Perform engine servicing, oil changes, filter replacement, and component inspections.Maintain propellers, Auxiliary Power Units (APU), and fuel systems.Monitor engine performance and recommend corrective actions.Avionics & Electrical SystemsInspect communication and navigation systems.Maintain radar, autopilot, cockpit instrumentation, and electrical wiring.Test aircraft electronic systems for operational reliability.Ensure compliance with avionics maintenance procedures.Documentation & ComplianceComplete maintenance logs, inspection reports, and defect records.Maintain aircraft technical documentation accurately.Ensure compliance with aviation regulatory authorities.Certify aircraft for return to service after maintenance (where appropriately licensed).Follow company maintenance policies and quality assurance procedures.Safety & Quality AssuranceFollow all aviation safety regulations and standard operating procedures.Maintain clean and organized work areas.Ensure proper use of Personal Protective Equipment (PPE).Report safety hazards and technical discrepancies immediately.Participate in safety audits and quality inspections.Team CoordinationWork closely with pilots, technicians, quality inspectors, and operations staff.Coordinate maintenance schedules with flight operations.Assist junior technicians with technical guidance and training.Participate in emergency aircraft recovery and AOG (Aircraft on Ground) support.Required QualificationsDiploma or Bachelor's Degree in Aircraft Maintenance Engineering, Aeronautical Engineering, Mechanical Engineering, or Aerospace Engineering.DGCA-approved AME qualification or equivalent aviation authority certification is preferred.Valid Aircraft Maintenance Engineer License (where applicable).Type rating on specific aircraft is an advantage.Relevant experience in aircraft maintenance is preferred.Required SkillsStrong knowledge of aircraft systems and maintenance procedures.Excellent troubleshooting and fault diagnosis skills.Knowledge of aviation regulations and airworthiness standards.Ability to interpret aircraft maintenance manuals and engineering drawings.Strong analytical and problem-solving abilities.Excellent attention to detail.Good communication and teamwork skills.Ability to work under pressure and meet strict deadlines.Computer proficiency in maintenance management software.Good technical documentation skills.Technical KnowledgeAircraft StructuresGas Turbine EnginesHydraulic SystemsPneumatic SystemsElectrical SystemsAvionics SystemsFlight Control SystemsLanding Gear SystemsFuel SystemsAircraft DocumentationMaintenance PlanningAircraft Safety StandardsPreferred CertificationsDGCA Aircraft Maintenance Engineer LicenseEASA Part-66 License (preferred internationally)ICAO-compliant aviation trainingHuman Factors TrainingSafety Management System (SMS) TrainingFuel Tank Safety TrainingEWIS (Electrical Wiring Interconnection System) TrainingAircraft Type Rating CertificationWorking ConditionsAirport hangars, maintenance bases, and line maintenance stations.Rotational shifts including nights, weekends, and public holidays.Outdoor work in varying weather conditions.Physically demanding work involving standing, climbing, bending, and lifting equipment.Exposure to aircraft noise, fuels, lubricants, and hydraulic fluids while following strict safety procedures.Salary Range (India)Fresher: 3.5 - 6 LPA2-5 Years: 6 - 10 LPA5-10 Years: 10 - 18 LPALicensed/Type-Rated AME: 15 - 30+ LPA (depending on airline, aircraft type, and experience)

We are seeking a motivated Field Service Engineer to join our team in Bangalore. This entry-level position is ideal for candidates with an I.T.I. qualification who are eager to start their careers in the engineering field. The role involves ensuring that equipment is installed and maintained to meet customer satisfaction.Key Responsibilities:1. Installation and Setup: You will be responsible for setting up and installing equipment at client locations, ensuring everything is operational and meets quality standards.2. Maintenance and Repair: Conduct regular maintenance checks and perform necessary repairs on equipment to prevent malfunctions and extend the lifespan of devices.3. Customer Support: Provide excellent customer service, addressing any technical issues and answering client queries to ensure a smooth experience.4. Documentation: Maintain accurate records of service operations, including installation details and maintenance logs, to keep track of all activities.5. Collaboration: Work closely with your team and other departments to ensure that service goals and customer expectations are met.Required Skills and Expectations:Candidates should possess strong problem-solving abilities and technical skills related to equipment maintenance. Good communication skills are essential for interacting with clients and addressing their needs effectively. A willingness to learn and adapt to new technologies is important, as is the ability to work as part of a team. A clean driving record and readiness to travel for field service tasks may also be required.

Job DetailFreshers Roustabout For Offshore Project (Abu Dhabi) - FreshersOil / Gas / Petroleum Ajman, UAEInfoCandidatesPremium JobRe-Post JobDeleteRecommended SeekersIndustry : Oil / Gas / PetroleumKey Skills : Rigger, Roustabout, Petrochemical, Petroleum Engineer, BE Mechanical, Offshore, Offshore Platforms, Offshore Drilling, Diploma Trainee, Diploma Fitter, Diploma Engineer, Diploma Trainee Engineer, Diploma Mechanical Engineer,Function : Oil & FilterPositions : 350Experience : 0 - 4 Yrs.Salary : INR 1200000 - 2000000Additional Perks : Flexible Working Hours, Overtime Pay, Joining Bonus, Annual Bonus, Travel Allowance (TA), Petrol Allowance, Mobile Allowance, Internet Allowance, Health Insurance, Food/Meals, AccommodationLocation(s) of Job : Ajman, UAEQualification : Graduate (B.A, B.C.A, B.Com, B.Sc, B.Tech/B.E, Vocational Course, Professional Degree, Certificate/Diploma/Others)Gender Preference : MaleAge Limit : 18 - 40 Yrs.Hiring For : Own CompanyType of interview : TelephonicDESCRIPTIONAs a Roustabout, you will play an essential role in supporting operations in the oil and gas industry. Your primary focus will be on maintaining a clean and safe work area, as well as assisting with various tasks on site.Key Responsibilities:- Maintaining Equipment: Assist in the upkeep and cleaning of tools and machinery to ensure they are in good working condition, which helps to prevent accidents and delays.- Loading and Unloading Supplies: Help in the movement of equipment and materials to and from the worksite, ensuring that everything is handled safely and efficiently.- Cleaning Work Areas: Regularly clean and organize workspaces, which contributes to a safe and tidy environment for all workers.- Assisting Technicians: Work alongside skilled professionals to support their tasks, gaining hands-on experience and understanding of the job.- Observing Safety Protocols: Follow all safety regulations and procedures to protect yourself and your coworkers from hazards on the job site.Required Skills and Expectations:- Team Player: Ability to work well with others and communicate effectively, as collaboration is crucial in the workplace.- Physical Fitness: Must be able to perform physical tasks, such as lifting heavy objects and standing for long periods.- Basic Technical Knowledge: Familiarity with basic tools and their uses is beneficial, even if you are new to the field.- Adaptable and Willing to Learn: An eagerness to take on new tasks and learn from experienced colleagues will help you grow in this role.- Attention to Detail: Be observant and conscientious about following instructions and maintaining safety.

Visa duration- 12 months to 3 yearsFree medical and education facilities for familyFamily visaGovt sponsored visaSpouse can legally workSelection on first cum first basisClients should have sufficient funds to sustain in the countryFree medical insurance.Fast process

Candidate job profile :-As a Service Engineer with a specialization in Electrical Engineering, you responsible for maintaining and improving electrical systems. Your role will involve troubleshooting issues, performing regular maintenance, and ensuring systems operate efficiently and safely. This position requires on-site support, technical expertise, and strong problem-solving skills.ResponsibilitiesTroubleshoot and resolve electrical system issues.Perform regular maintenance and inspections of electrical systems.Ensure compliance with safety and regulatory standards.Collaborate with other engineers and technicians to improve efficiency.Document service and maintenance activities accurately.Provide on-site technical support as needed.Manage and prioritize a schedule of multiple service tasks.

An Aircraft Maintenance Engineer (AME) is responsible for ensuring that aircraft are safe, airworthy, and ready for flight. They inspect, repair, maintain, and certify aircraft systems in compliance with aviation safety standards. Key ResponsibilitiesPerform routine inspections before and after flightsDiagnose and troubleshoot aircraft mechanical/electrical issuesRepair and replace faulty components (engines, hydraulics, avionics)Conduct scheduled maintenance checks (A, B, C, D checks)Maintain accurate maintenance logs and documentationEnsure compliance with aviation authorities like DGCACertify aircraft as airworthy for operationWork closely with pilots and ground staff Skills RequiredStrong knowledge of aircraft systems & engineering principlesAttention to detail and safety awarenessProblem-solving and troubleshooting skillsTechnical proficiency with tools and diagnostic equipmentTeamwork and communication skills Educational QualificationAME Course approved by DGCAOR Diploma/Degree in Aeronautical EngineeringLicensing is mandatory (Category B1/B2) Work EnvironmentAirports, hangars, maintenance basesShift-based work (including nights & weekends)Physically demanding and safety-critical role Salary (India Approx.)Fresher: 3 - 5 LPAExperienced: 6 - 15+ LPA

DESCRIPTIONJob descriptionTeam member - Drilling Responsibilities The role is responsible for supporting Drilling & Completion (D&C) offshore activities, encompassing the planning, execution, and delivery of offshore exploratory and development drilling operations. The position contributes to ensuring technical integrity, operational safety, and execution efficiency across all offshore drilling activities. The role involves managing and mentoring a team of engineers, coordinating closely with subsurface, completion, and other crossfunctional teams, and providing technical oversight throughout the well lifecycle. A key responsibility includes ensuring strict compliance with HSSE standards, optimizing well designs, and driving continuous improvement in contractor performance and operational outcomes. This position requires a strong technical foundation in well engineering and offshore drilling operations, coupled with proven leadership, communication, and stakeholdermanagement capabilities, to effectively deliver safe, efficient, and costeffective offshore wells. HSSE Leadership: Exhibit a strong personal commitment to HSSE by setting an example and fostering a safety-first culture. Ensuring that all D&C activities are conducted in accordance with the highest level of safety and environmental standards. Drilling Engineering and Operations Management: Support and supervise the technical integrity and assurance of well designs, ensuring full integration between subsurface and wells teams during planning. Collaborate with the subsurface team to develop and maintain the Drilling Basis of Design (BoD). Conduct front-end planning for development wells, optimizing well designs, casing, cementing, and fluid programs. Perform technical risk assessments, contingency planning, and develop mitigation strategies for all drilling activities. Evaluate existing well designs and recommend optimizations to enhance operational efficiency. Lead and coordinate the execution of offshore drilling operations. Ensure comprehensive delivery of detailed field development drilling engineering. Cost and Resource Management: Prepare cost estimates for drilling projects. Review and optimize the Schedule of Rates and drilling programs. Contracting & Vendor Management: Oversee the entire contracting process, from preparing scopes of work to selecting rigs, well equipment, and services. Ensure alignment of all technical elements and commercial recommendations with the company's operational goals. Serving as the primary contact for well planning issues and contractor coordination. Lead contractor performance management, ensuring high standards from rigs, equipment, and well service providers. Team Leadership & Coordination: Manage and mentor a team of drilling engineers, providing guidance and technical authority throughout drilling operations. Ensure seamless coordination between in-house technical support and external drilling service providers. Regulatory & Audit Compliance: Ensure that drilling operations adhere to national and international regulations and standards. Participate in audits of rig/well sites and service bases to ensure compliance with international standards. Reporting & Stakeholder Management: Prepare and present regular reports on drilling operations, cost estimates, and project progress to senior management. Communicate with key internal and external stakeholders to ensure alignment of operational objectives. Qualifications Must: Master's or bachelor's degree within Petroleum Engineering 8-12 years of relevant work experience Demonstrated business acumen and abilities to lead teams Demonstrated experience dealing with suppliers and/or customers Excellent written and verbal communications skills Work experience in a multicultural and changing environment.

DESCRIPTIONWe are looking for a dedicated and hardworking Roustabout to join our team in Saudi Arabia. As a Roustabout, you will play a crucial role in supporting various operations, ensuring that tasks are completed safely and efficiently.Key Responsibilities:- Assist with Rig Operations: Support the rig crew in setting up, maintaining, and dismantling equipment used in drilling operations. This includes handling tools and materials needed for efficient workflow.- General Maintenance: Help with the upkeep of the work site and equipment to ensure a safe and clean environment. This involves cleaning decks, managing waste, and performing minor repairs as needed.- Material Handling: Load and unload equipment and supplies, ensuring that all items are transported safely and securely to the proper locations on site.- Safety Compliance: Follow safety procedures and guidelines to ensure personal safety and the safety of others on the site. This includes wearing appropriate safety gear and participating in safety drills.- Team Cooperation: Work closely with other crew members, showing teamwork and communication skills to ensure tasks are completed effectively and on time.Required Skills and Expectations:- Must have completed at least the 12th grade education.- Strong physical stamina and fitness, as the job involves manual labor and working in various weather conditions.- Willingness to learn and follow instructions from supervisors.- Basic understanding of safety practices in industrial environments is a plus.- Positive attitude and ability to work in a team-oriented environment.- Must be male, as per job requirements.

As an Aircraft Maintenance Engineer, you will play a vital role in ensuring the safety and reliability of aircraft. You will be responsible for performing maintenance, repairs, and inspections on various aircraft systems. Key Responsibilities:- Conduct Routine Inspections: Regularly check aircraft systems, engines, and structures to ensure they meet safety standards and operational requirements.- Perform Repairs: Diagnose and fix issues with aircraft components such as engines, electrical systems, and landing gear to maintain high operational performance.- Documentation: Maintain accurate records of all maintenance activities and inspections performed to comply with aviation regulations and standards.- Collaborate with Team: Work closely with other engineers and technicians to share knowledge and ensure that all maintenance tasks are completed efficiently and safely.- Adhere to Safety Regulations: Follow all safety protocols and guidelines to maintain a safe working environment for yourself and your colleagues.Required Skills and Expectations:A good candidate should have a keen attention to detail, as accuracy is critical in aviation. Effective communication and teamwork skills are essential to work well with other professionals in the field. The ability to problem-solve quickly and efficiently is important, especially when dealing with unexpected issues. Basic technical knowledge of aviation systems and a strong commitment to safety and compliance with regulations are crucial. Candidates with a background in engineering or a strong interest in aircraft maintenance will find this position rewarding.

We are looking for an Aircraft Maintenance Engineer to join our team in Kochi. As an Aircraft Maintenance Engineer, you will play a crucial role in ensuring the safety and efficiency of our aircraft through regular inspections and repairs. Your primary responsibilities will include:- Conducting Inspections: Perform routine and non-routine inspections of aircraft to identify potential problems, ensuring compliance with safety standards and regulations.- Carrying Out Repairs: Diagnose mechanical issues and carry out necessary repairs on aircraft systems, including engines, avionics, and airframe components.- Maintaining Records: Document all maintenance activities, including inspections and repairs, to ensure accurate and up-to-date maintenance logs and compliance with industry regulations.- Collaborating with Team Members: Work closely with other maintenance staff and engineers to ensure timely completion of maintenance tasks and coordination of schedules.- Staying Informed: Keep yourself updated with the latest aviation regulations, techniques, and technologies to improve personal skills and enhance overall maintenance practices.To be successful in this role, you should have a solid understanding of aviation principles and aircraft systems. Strong problem-solving skills and attention to detail are essential. You should also have excellent communication skills to collaborate effectively with team members and report findings accurately. A valid Aircraft Maintenance Engineer license or certification is preferred, though not mandatory for entry-level applicants. Being a team player with a safety-first mindset is crucial for this position.

As an Aircraft Maintenance Engineer, you will play a crucial role in ensuring the safety and efficiency of aircraft. Your primary responsibilities will include:- Conducting Inspections: Regularly check aircraft to ensure they are in proper working condition. This involves identifying any mechanical issues and verifying compliance with safety regulations.- Performing Repairs: Fix any faults discovered during inspections or reported by the flight crew. This can include everything from minor adjustments to major repairs on engines or electrical systems.- Maintaining Records: Keep detailed records of all maintenance work done on aircraft. Accurate documentation is essential for safety audits and regulatory compliance.- Collaborating with Team Members: Work closely with other engineers and technicians to handle repairs and maintenance effectively. Good communication is vital for a cohesive working environment.- Staying Updated on Technology: Keep up with the latest in aviation technology and maintenance practices. Continuous learning ensures you are equipped to handle new aircraft systems and technologies.To be successful in this role, you should have strong technical skills and a good understanding of aircraft systems. Attention to detail is crucial, as even minor oversights can lead to significant safety risks. Good problem-solving skills will help you tackle complex maintenance issues effectively. You should also demonstrate a commitment to safety and adhere strictly to regulatory standards. Open communication and teamwork abilities are essential to work effectively in a collaborative environment.

Job TitleAircraft Maintenance Engineer (AME)DepartmentAircraft Maintenance / EngineeringLocationsGuwahatiImphalKolkataAizwalItanagarTezuJorhatSilcharShillongDimapurGangtokAgartalaJob SummaryAn Aircraft Maintenance Engineer (AME) is responsible for inspecting, maintaining, repairing, troubleshooting, and certifying aircraft to ensure they are safe, airworthy, and compliant with aviation regulations. The role involves carrying out scheduled and unscheduled maintenance on aircraft systems, engines, avionics, electrical components, hydraulic systems, landing gear, and structural components while adhering to the standards established by aviation authorities.Key ResponsibilitiesAircraft Inspection & MaintenancePerform routine, preventive, scheduled, and unscheduled aircraft maintenance.Conduct daily, transit, weekly, A-check, B-check, C-check, and heavy maintenance inspections.Inspect aircraft structures, fuselage, wings, landing gear, flight controls, and engines.Diagnose and rectify aircraft defects using approved maintenance procedures.Replace, repair, and overhaul defective aircraft components.Ensure all maintenance tasks are completed according to the Aircraft Maintenance Manual (AMM).Troubleshooting & RepairsIdentify mechanical, hydraulic, electrical, pneumatic, and avionics faults.Use specialized diagnostic tools and testing equipment.Repair aircraft systems while maintaining manufacturer specifications.Coordinate with engineering teams for complex technical issues.Perform functional tests after repairs to verify serviceability.Engine & Component MaintenanceInspect aircraft engines for wear, leaks, corrosion, and damage.Perform engine servicing, oil changes, filter replacement, and component inspections.Maintain propellers, Auxiliary Power Units (APU), and fuel systems.Monitor engine performance and recommend corrective actions.Avionics & Electrical SystemsInspect communication and navigation systems.Maintain radar, autopilot, cockpit instrumentation, and electrical wiring.Test aircraft electronic systems for operational reliability.Ensure compliance with avionics maintenance procedures.Documentation & ComplianceComplete maintenance logs, inspection reports, and defect records.Maintain aircraft technical documentation accurately.Ensure compliance with aviation regulatory authorities.Certify aircraft for return to service after maintenance (where appropriately licensed).Follow company maintenance policies and quality assurance procedures.Safety & Quality AssuranceFollow all aviation safety regulations and standard operating procedures.Maintain clean and organized work areas.Ensure proper use of Personal Protective Equipment (PPE).Report safety hazards and technical discrepancies immediately.Participate in safety audits and quality inspections.Team CoordinationWork closely with pilots, technicians, quality inspectors, and operations staff.Coordinate maintenance schedules with flight operations.Assist junior technicians with technical guidance and training.Participate in emergency aircraft recovery and AOG (Aircraft on Ground) support.Required QualificationsDiploma or Bachelor's Degree in Aircraft Maintenance Engineering, Aeronautical Engineering, Mechanical Engineering, or Aerospace Engineering.DGCA-approved AME qualification or equivalent aviation authority certification is preferred.Valid Aircraft Maintenance Engineer License (where applicable).Type rating on specific aircraft is an advantage.Relevant experience in aircraft maintenance is preferred.Required SkillsStrong knowledge of aircraft systems and maintenance procedures.Excellent troubleshooting and fault diagnosis skills.Knowledge of aviation regulations and airworthiness standards.Ability to interpret aircraft maintenance manuals and engineering drawings.Strong analytical and problem-solving abilities.Excellent attention to detail.Good communication and teamwork skills.Ability to work under pressure and meet strict deadlines.Computer proficiency in maintenance management software.Good technical documentation skills.Technical KnowledgeAircraft StructuresGas Turbine EnginesHydraulic SystemsPneumatic SystemsElectrical SystemsAvionics SystemsFlight Control SystemsLanding Gear SystemsFuel SystemsAircraft DocumentationMaintenance PlanningAircraft Safety StandardsPreferred CertificationsDGCA Aircraft Maintenance Engineer LicenseEASA Part-66 License (preferred internationally)ICAO-compliant aviation trainingHuman Factors TrainingSafety Management System (SMS) TrainingFuel Tank Safety TrainingEWIS (Electrical Wiring Interconnection System) TrainingAircraft Type Rating CertificationWorking ConditionsAirport hangars, maintenance bases, and line maintenance stations.Rotational shifts including nights, weekends, and public holidays.Outdoor work in varying weather conditions.Physically demanding work involving standing, climbing, bending, and lifting equipment.Exposure to aircraft noise, fuels, lubricants, and hydraulic fluids while following strict safety procedures.Salary Range (India)Fresher: 3.5 - 6 LPA2-5 Years: 6 - 10 LPA5-10 Years: 10 - 18 LPALicensed/Type-Rated AME: 15 - 30+ LPA (depending on airline, aircraft type, and experience)

Job TitleAircraft Maintenance Engineer (AME)DepartmentAircraft Maintenance / EngineeringLocationsBangaloreMangaloreBelagaviBallariBidarHubliKalaburgiKoppalMysoreShivamoggaJob SummaryAn Aircraft Maintenance Engineer (AME) is responsible for inspecting, maintaining, repairing, troubleshooting, and certifying aircraft to ensure they are safe, airworthy, and compliant with aviation regulations. The role involves carrying out scheduled and unscheduled maintenance on aircraft systems, engines, avionics, electrical components, hydraulic systems, landing gear, and structural components while adhering to the standards established by aviation authorities.Key ResponsibilitiesAircraft Inspection & MaintenancePerform routine, preventive, scheduled, and unscheduled aircraft maintenance.Conduct daily, transit, weekly, A-check, B-check, C-check, and heavy maintenance inspections.Inspect aircraft structures, fuselage, wings, landing gear, flight controls, and engines.Diagnose and rectify aircraft defects using approved maintenance procedures.Replace, repair, and overhaul defective aircraft components.Ensure all maintenance tasks are completed according to the Aircraft Maintenance Manual (AMM).Troubleshooting & RepairsIdentify mechanical, hydraulic, electrical, pneumatic, and avionics faults.Use specialized diagnostic tools and testing equipment.Repair aircraft systems while maintaining manufacturer specifications.Coordinate with engineering teams for complex technical issues.Perform functional tests after repairs to verify serviceability.Engine & Component MaintenanceInspect aircraft engines for wear, leaks, corrosion, and damage.Perform engine servicing, oil changes, filter replacement, and component inspections.Maintain propellers, Auxiliary Power Units (APU), and fuel systems.Monitor engine performance and recommend corrective actions.Avionics & Electrical SystemsInspect communication and navigation systems.Maintain radar, autopilot, cockpit instrumentation, and electrical wiring.Test aircraft electronic systems for operational reliability.Ensure compliance with avionics maintenance procedures.Documentation & ComplianceComplete maintenance logs, inspection reports, and defect records.Maintain aircraft technical documentation accurately.Ensure compliance with aviation regulatory authorities.Certify aircraft for return to service after maintenance (where appropriately licensed).Follow company maintenance policies and quality assurance procedures.Safety & Quality AssuranceFollow all aviation safety regulations and standard operating procedures.Maintain clean and organized work areas.Ensure proper use of Personal Protective Equipment (PPE).Report safety hazards and technical discrepancies immediately.Participate in safety audits and quality inspections.Team CoordinationWork closely with pilots, technicians, quality inspectors, and operations staff.Coordinate maintenance schedules with flight operations.Assist junior technicians with technical guidance and training.Participate in emergency aircraft recovery and AOG (Aircraft on Ground) support.Required QualificationsDiploma or Bachelor's Degree in Aircraft Maintenance Engineering, Aeronautical Engineering, Mechanical Engineering, or Aerospace Engineering.DGCA-approved AME qualification or equivalent aviation authority certification is preferred.Valid Aircraft Maintenance Engineer License (where applicable).Type rating on specific aircraft is an advantage.Relevant experience in aircraft maintenance is preferred.Required SkillsStrong knowledge of aircraft systems and maintenance procedures.Excellent troubleshooting and fault diagnosis skills.Knowledge of aviation regulations and airworthiness standards.Ability to interpret aircraft maintenance manuals and engineering drawings.Strong analytical and problem-solving abilities.Excellent attention to detail.Good communication and teamwork skills.Ability to work under pressure and meet strict deadlines.Computer proficiency in maintenance management software.Good technical documentation skills.Technical KnowledgeAircraft StructuresGas Turbine EnginesHydraulic SystemsPneumatic SystemsElectrical SystemsAvionics SystemsFlight Control SystemsLanding Gear SystemsFuel SystemsAircraft DocumentationMaintenance PlanningAircraft Safety StandardsPreferred CertificationsDGCA Aircraft Maintenance Engineer LicenseEASA Part-66 License (preferred internationally)ICAO-compliant aviation trainingHuman Factors TrainingSafety Management System (SMS) TrainingFuel Tank Safety TrainingEWIS (Electrical Wiring Interconnection System) TrainingAircraft Type Rating CertificationWorking ConditionsAirport hangars, maintenance bases, and line maintenance stations.Rotational shifts including nights, weekends, and public holidays.Outdoor work in varying weather conditions.Physically demanding work involving standing, climbing, bending, and lifting equipment.Exposure to aircraft noise, fuels, lubricants, and hydraulic fluids while following strict safety procedures.Salary Range (India)Fresher: 3.5 - 6 LPA2-5 Years: 6 - 10 LPA5-10 Years: 10 - 18 LPALicensed/Type-Rated AME: 15 - 30+ LPA (depending on airline, aircraft type, and experience)

Job TitleAircraft Maintenance Engineer (AME)DepartmentAircraft Maintenance / EngineeringLocationsChennaiJob SummaryAn Aircraft Maintenance Engineer (AME) is responsible for inspecting, maintaining, repairing, troubleshooting, and certifying aircraft to ensure they are safe, airworthy, and compliant with aviation regulations. The role involves carrying out scheduled and unscheduled maintenance on aircraft systems, engines, avionics, electrical components, hydraulic systems, landing gear, and structural components while adhering to the standards established by aviation authorities.Key ResponsibilitiesAircraft Inspection & MaintenancePerform routine, preventive, scheduled, and unscheduled aircraft maintenance.Conduct daily, transit, weekly, A-check, B-check, C-check, and heavy maintenance inspections.Inspect aircraft structures, fuselage, wings, landing gear, flight controls, and engines.Diagnose and rectify aircraft defects using approved maintenance procedures.Replace, repair, and overhaul defective aircraft components.Ensure all maintenance tasks are completed according to the Aircraft Maintenance Manual (AMM).Troubleshooting & RepairsIdentify mechanical, hydraulic, electrical, pneumatic, and avionics faults.Use specialized diagnostic tools and testing equipment.Repair aircraft systems while maintaining manufacturer specifications.Coordinate with engineering teams for complex technical issues.Perform functional tests after repairs to verify serviceability.Engine & Component MaintenanceInspect aircraft engines for wear, leaks, corrosion, and damage.Perform engine servicing, oil changes, filter replacement, and component inspections.Maintain propellers, Auxiliary Power Units (APU), and fuel systems.Monitor engine performance and recommend corrective actions.Avionics & Electrical SystemsInspect communication and navigation systems.Maintain radar, autopilot, cockpit instrumentation, and electrical wiring.Test aircraft electronic systems for operational reliability.Ensure compliance with avionics maintenance procedures.Documentation & ComplianceComplete maintenance logs, inspection reports, and defect records.Maintain aircraft technical documentation accurately.Ensure compliance with aviation regulatory authorities.Certify aircraft for return to service after maintenance (where appropriately licensed).Follow company maintenance policies and quality assurance procedures.Safety & Quality AssuranceFollow all aviation safety regulations and standard operating procedures.Maintain clean and organized work areas.Ensure proper use of Personal Protective Equipment (PPE).Report safety hazards and technical discrepancies immediately.Participate in safety audits and quality inspections.Team CoordinationWork closely with pilots, technicians, quality inspectors, and operations staff.Coordinate maintenance schedules with flight operations.Assist junior technicians with technical guidance and training.Participate in emergency aircraft recovery and AOG (Aircraft on Ground) support.Required QualificationsDiploma or Bachelor's Degree in Aircraft Maintenance Engineering, Aeronautical Engineering, Mechanical Engineering, or Aerospace Engineering.DGCA-approved AME qualification or equivalent aviation authority certification is preferred.Valid Aircraft Maintenance Engineer License (where applicable).Type rating on specific aircraft is an advantage.Relevant experience in aircraft maintenance is preferred.Required SkillsStrong knowledge of aircraft systems and maintenance procedures.Excellent troubleshooting and fault diagnosis skills.Knowledge of aviation regulations and airworthiness standards.Ability to interpret aircraft maintenance manuals and engineering drawings.Strong analytical and problem-solving abilities.Excellent attention to detail.Good communication and teamwork skills.Ability to work under pressure and meet strict deadlines.Computer proficiency in maintenance management software.Good technical documentation skills.Technical KnowledgeAircraft StructuresGas Turbine EnginesHydraulic SystemsPneumatic SystemsElectrical SystemsAvionics SystemsFlight Control SystemsLanding Gear SystemsFuel SystemsAircraft DocumentationMaintenance PlanningAircraft Safety StandardsPreferred CertificationsDGCA Aircraft Maintenance Engineer LicenseEASA Part-66 License (preferred internationally)ICAO-compliant aviation trainingHuman Factors TrainingSafety Management System (SMS) TrainingFuel Tank Safety TrainingEWIS (Electrical Wiring Interconnection System) TrainingAircraft Type Rating CertificationWorking ConditionsAirport hangars, maintenance bases, and line maintenance stations.Rotational shifts including nights, weekends, and public holidays.Outdoor work in varying weather conditions.Physically demanding work involving standing, climbing, bending, and lifting equipment.Exposure to aircraft noise, fuels, lubricants, and hydraulic fluids while following strict safety procedures.Salary Range (India)Fresher: 3.5 - 6 LPA2-5 Years: 6 - 10 LPA5-10 Years: 10 - 18 LPALicensed/Type-Rated AME: 15 - 30+ LPA (depending on airline, aircraft type, and experience)

As a Field Service Engineer based in Mysore, you will be responsible for providing technical support and solutions at customer locations. You will handle installation, maintenance, and repair of equipment while ensuring high levels of customer satisfaction.Key Responsibilities:- Installation of Equipment: You will set up and install machinery at client sites according to specifications, ensuring they are operational and meet safety standards.- Maintenance and Repair: Regularly conduct preventative maintenance and emergency repairs on equipment, minimizing downtime for clients.- Troubleshooting: Identify issues with equipment using diagnostic tools and provide effective solutions to restore functioning.- Customer Support: Communicate with clients to understand their needs and explain technical issues clearly, ensuring they feel supported throughout the service process.- Documentation: Maintain accurate records of service visits, repairs, and customer feedback to inform future actions and improvements.Required Skills and Expectations:Candidates should possess a strong foundation in technical skills, preferably with an I.T.I. certification. You are expected to have excellent problem-solving abilities and a hands-on approach to repairing equipment. Good communication skills are essential for interacting with customers effectively. A willingness to learn new technologies and a proactive attitude are important. Additionally, since this role is for male candidates, applicants should be prepared for possible travel to client sites and flexible working hours to meet customer needs.

Description : Develop and formulate new food products based on market requirements.Test and improve existing food products, recipes, and formulations.Conduct quality checks on raw materials, ingredients, and finished products.Ensure compliance with food safety, hygiene, and quality standards.Monitor food processing and production activities.Conduct shelf-life and stability studies for food products.Perform sensory evaluation of food products for taste, texture, aroma, and appearance.Research new ingredients, food technologies, and preservation methods.Coordinate with production, quality control, and R&D teams.Identify and resolve product quality and processing issues.Maintain product specifications, laboratory records, and technical reports.Assist in developing nutritional information and product labels.Ensure proper storage and handling of ingredients and finished products.Support audits and maintain food safety documentation.Stay updated on food industry regulations, standards, and new technologies.

Key Responsibilities:Install, inspect, maintain, and troubleshoot biomedical and medical equipment.Perform preventive and corrective maintenance of medical devices.Ensure proper calibration and functioning of equipment.Coordinate with hospital staff and equipment vendors for technical support.Maintain equipment service records, maintenance logs, and documentation.Assist in equipment procurement, evaluation, and installation.Ensure medical equipment complies with safety and quality standards.Provide technical guidance and basic training to healthcare staff.Identify equipment issues and coordinate timely repairs.Follow hospital safety procedures and biomedical equipment protocols.Eligibility / Qualification:B.E./B.Tech in Biomedical Engineering.Freshers and experienced candidates can apply.Good communication and problem-solving skills.Basic knowledge of medical equipment and troubleshooting is preferred.

We are looking for a Paramedical Technician to join our team in Tirumala, Chittoor. This is a full-time office-based position suitable for recent graduates.In this role, you will primarily be responsible for medical coding, which involves converting healthcare service-related text into numeric diagnosis and procedure codes using ICD-10 CM and CPT coding systems. You will work with healthcare documents to ensure accurate coding, contributing to efficient healthcare service management.Key responsibilities include:- Medical Coding: Utilize ICD-10 CM and CPT coding systems to convert healthcare information into numeric codes accurately.- Record Maintenance: Ensure all medical records are updated and maintained in compliance with healthcare standards.- Collaboration: Work closely with other healthcare professionals to ensure coding accuracy and compliance.To succeed in this role, you should possess strong analytical skills and attention to detail. A background in life sciences or paramedical studies is essential, as is a familiarity with medical terminology. You should also be adept at using coding software and have a commitment to maintaining confidentiality in line with healthcare regulations.The position requires a graduate level of education and offers an opportunity to gain valuable experience in the healthcare sector. If you are a motivated individual keen to start your career as a Paramedical Technician, we encourage you to apply.

As an Electronics Engineer, you will play a crucial role in designing, developing, and testing various electronic systems and components. Your responsibilities will include:- Circuit Design: Create and optimize circuit designs for electronic devices, ensuring they meet specifications and functionality requirements.- Prototyping: Develop prototypes to test the performance of electronic systems, allowing for adjustments and improvements before final production.- Testing and Evaluation: Conduct thorough testing of electronic components and systems, analyzing results to identify any issues and ensure quality standards are met.- Documentation: Maintain accurate documentation of designs, tests, and procedures to facilitate communication and compliance with industry standards.- Collaboration: Work closely with other engineers and teams to integrate electronic systems within larger projects, ensuring seamless operation and compatibility.- Troubleshooting: Quickly diagnose and resolve technical issues that arise during the design or testing phases, applying critical thinking and problem-solving skills.To succeed in this role, you should have a Bachelors degree in Electronics Engineering or a related field. A basic understanding of electronic circuit design, programming, and simulation software is essential. You should be familiar with using testing equipment like oscilloscopes and multimeters. Strong analytical skills, attention to detail, and the ability to work collaboratively in a team are key. Additionally, effective communication skills will help you convey technical information clearly to team members and stakeholders.

As a Cath LAB Technician, you will play a critical role in supporting cardiac procedures in a clinical environment. Your main responsibilities will include:- Assisting in Procedures: You will help doctors during catheterization and other cardiac procedures, ensuring that all equipment is ready and functioning properly.- Preparing Equipment: You will be responsible for setting up and testing all necessary instruments and machines, ensuring that everything is sterile and organized before procedures begin.- Monitoring Patient Status: During procedures, you will monitor patients' vital signs and provide real-time feedback to the medical team to ensure their safety and well-being.- Maintaining Inventory: You will keep track of supplies and materials used in the Cath Lab, ensuring that stock levels are adequate and reordering items as needed.- Documenting Procedures: You will record relevant data during procedures, including patient information, equipment used, and outcomes, to maintain accurate medical records.To be successful in this role, you should have a Bachelors degree in Science or an MBBS, and possess the following skills:- Technical Proficiency: Familiarity with medical equipment and technology used in a Cath Lab environment is essential.- Attention to Detail: You must be detail-oriented to ensure all procedures are conducted accurately and safely.- Team Collaboration: Strong communication and teamwork skills are important, as you will work closely with healthcare professionals to provide patient care.- Adaptability: You should be able to adjust quickly to changing situations and remain calm under pressure in a fast-paced environment.

Apply under Opportunity Card Germany visaGov. announced visaFamily visaWork and settle in GermanyFree education and medical facilities for familyCandidate is eligible to work in GermanyChild tax benefits givenPension plan givenUnemployment wages givenSalary equal to citizen of GermanyAll post landing services will be guided before landing GermanyCandidate will enjoy dual citizenship

Job for Electrical diploma holder candidateCandidate job profile :-As a Service Engineer with a specialization in Electrical Engineering, you responsible for maintaining and improving electrical systems. Your role will involve troubleshooting issues, performing regular maintenance, and ensuring systems operate efficiently and safely. This position requires on-site support, technical expertise, and strong problem-solving skills.ResponsibilitiesTroubleshoot and resolve electrical system issues.Perform regular maintenance and inspections of electrical systems.Ensure compliance with safety and regulatory standards.Collaborate with other engineers and technicians to improve efficiency.Document service and maintenance activities accurately.Provide on-site technical support as needed.Manage and prioritize a schedule of multiple service tasks.

Job for BE, BTech and Electrical diploma holder candidateCandidate job profile :-As a Service Engineer with a specialization in Electrical Engineering, you responsible for maintaining and improving electrical systems. Your role will involve troubleshooting issues, performing regular maintenance, and ensuring systems operate efficiently and safely. This position requires on-site support, technical expertise, and strong problem-solving skills.ResponsibilitiesTroubleshoot and resolve electrical system issues.Perform regular maintenance and inspections of electrical systems.Ensure compliance with safety and regulatory standards.Collaborate with other engineers and technicians to improve efficiency.Document service and maintenance activities accurately.Provide on-site technical support as needed.Manage and prioritize a schedule of multiple service tasks.

Job for Electrical diploma holder candidateCandidate job profile :-As a Service Engineer with a specialization in Electrical Engineering, you responsible for maintaining and improving electrical systems. Your role will involve troubleshooting issues, performing regular maintenance, and ensuring systems operate efficiently and safely. This position requires on-site support, technical expertise, and strong problem-solving skills.ResponsibilitiesTroubleshoot and resolve electrical system issues.Perform regular maintenance and inspections of electrical systems.Ensure compliance with safety and regulatory standards.Collaborate with other engineers and technicians to improve efficiency.Document service and maintenance activities accurately.Provide on-site technical support as needed.Manage and prioritize a schedule of multiple service tasks.

We are seeking a motivated Junior Engineer to join our team in Anna Nagar, Chennai. This full-time role is suitable for recent graduates and those with up to 2 years of experience in relevant fields.As a Junior Engineer, your key responsibilities will include assisting in the installation and maintenance of electronic low voltage systems such as CCTV and automation systems. You will be involved in networking tasks and will gain hands-on experience on-site. The role requires you to travel for site visits, supporting various projects as necessary. Strong communication skills in both Tamil and English will be essential for effective teamwork and client interactions.To be successful in this role, you should hold a Diploma or Bachelor's degree in Electrical and Electronics Engineering (ECE), Electrical Engineering (EEE), Electronics and Instrumentation (E&I), Computer Science, or a related field. Basic knowledge of electrical and networking concepts is expected. You should be willing to travel and work on-site, which may include the requirement for a valid driving license for travel purposes. Familiarity with ELV systems will be advantageous.Candidates must possess good problem-solving skills and a proactive attitude towards learning. This position offers an excellent opportunity to begin your engineering career in a hands-on environment, working collaboratively with experienced professionals.

Immediate opening for Electrical Technician in leading Manufacturing Industry Location - Chennai salary - 18k to 22k Experience -0yr to 1yr ( in any manufacturing Industry ) No of opening - 5